Winterizing plugs keep water from flowing back into your pool's plumbing after the lines are blown out, so nothing is left in the pipes to freeze and crack. The right plug depends on where it goes (return fitting, open pipe, skimmer, or main drain line) and how the opening is built (threaded or smooth). This guide covers the main plug types, how to size them, and how to install them so they hold all winter.
Do You Need to Winterize Your Pool?
Winterizing plugs are for pools that will be shut down through freezing weather. If your area gets hard, sustained freezes, the plumbing needs to be cleared of water and sealed before the cold arrives. In milder climates, including much of the Phoenix area, many pools keep running through winter instead, and the pump's circulation does the protecting. If you are not sure which approach fits your pool and location, ask a local pool professional before you shut anything down.
How Winterizing Plugs Work
The standard method is to blow air through each line with a shop vacuum, pool blower, or compressor until air bubbles out at the pool end, then seal the opening. The air left trapped in the pipe acts as a lock that keeps water from flowing back in. Industry guidance for inground pools calls for purging every line this way: returns, skimmer lines, the main drain, and lines to cleaners, water features, and solar heating.
The timing matters. Install each plug while air is still moving through the line. If you shut off the air first, water can rush back into the pipe before it is sealed.
Types of Pool Winterizing Plugs
Threaded Return Plugs
Most inground return fittings are threaded. Remove the directional eyeball fitting, then screw in a threaded winter plug. Plugs with an O-ring or gasket seal against the face of the fitting. Most residential return fittings take a 1-1/2-inch threaded plug, but check yours before buying, since some fittings and older pools use other sizes.
Options: 1-1/2-inch threaded winter plug and AquaGuard 1-1/2-inch threaded winter plug.
Rubber Expansion Plugs
Expansion plugs are for smooth, unthreaded openings such as an open pipe end or a slip socket. Tightening the wing nut squeezes the rubber so it expands against the pipe wall. They are sized to the pipe or socket, not to a thread. For example, a plug made for 1-1/2-inch pipe is wider than 1-1/2 inches so it can seal inside the opening. Some versions have a hollow stem with a valve that lets you blow air through the line before capping it.
Duck-Bill Plugs
A duck-bill plug such as the Anderson Winter Duck Plug screws into a 1-1/2-inch threaded fitting and contains a one-way valve. Air and water can be blown out of the line, but the valve keeps water from flowing back in. Because the plug can go in before you start blowing, one person can winterize the lines without running back and forth to set plugs. The manufacturer says this method can also avoid draining the pool below the returns, and it includes yellow safety caps for added protection against ice movement.
Skimmer Plugs and Skimmer Covers
Skimmers need two kinds of protection. The line at the bottom of the skimmer is plugged after it is blown out. The skimmer body also needs protection, because water that freezes inside it can crack it. On inground pools, an expansion device threaded into the skimmer gives the ice room to push against something other than the skimmer walls.
Above-ground pools usually use a cover plate or plug made for the skimmer model, which lets you close off the skimmer without draining the pool as low. For example, this above-ground skimmer plug fits Hayward SP1090 and SP1091LX square skimmers. Match the plug to your skimmer's model number.
How to Choose the Right Size
| Opening | What to measure | Plug type |
|---|---|---|
| Return fitting (eyeball removed) | Thread size of the fitting, usually 1-1/2" | Threaded plug or duck-bill plug |
| Open PVC pipe or slip socket | Nominal pipe size (1", 1-1/2", 2") | Rubber expansion plug sized for that pipe |
| Skimmer line | Opening size at the bottom of the skimmer | Threaded or expansion plug, per skimmer |
| Above-ground skimmer | Skimmer brand and model number | Model-specific skimmer plug or cover plate |
When in doubt, bring the eyeball fitting or a photo of the opening with a tape measure beside it into the store. Buy one or two spare plugs. They are inexpensive, and a lost or cracked plug at closing time can hold up the whole job.
How to Install Winterizing Plugs
- Balance and clean the water and lower the level as your cover and pool type require.
- Remove return eyeballs and skimmer baskets.
- Blow out each line with a shop vac, pool blower, or compressor until air bubbles steadily out at the pool end.
- Plug while the air is still flowing. For the main drain, keep the air running and close the drain valve at the equipment pad.
- Seal threads properly. On threaded plugs, a few wraps of thread-seal tape helps them seal. Tighten them snug by hand. Do not force them, since overtightening can damage plastic threads.
- Drain the equipment. Open the drain plugs on the pump, filter, heater, and any salt cell or chemical feeder, and store small removable parts indoors.
- Check after a day. If the water level in the pool rises around a plug or air keeps escaping, reseat that plug.
Follow your equipment manufacturers' winterizing instructions for heaters, salt systems, and automation, since each has its own drain points.
Common Mistakes
- Plugging after the air is shut off. Water flows back into the line and defeats the purpose.
- Wrong plug for the opening. An expansion plug forced into a threaded fitting, or the wrong thread size, will leak.
- Forgetting secondary lines. Cleaner lines, spa spillover, water features, and solar lines all need to be cleared.
- Leaving equipment full of water. Pumps, filters, and heaters crack just as easily as pipes.
Frequently Asked Questions
What size winterizing plug do I need for my pool returns?
Most residential return fittings take a 1-1/2-inch threaded plug once the eyeball is removed. Confirm the size on your fitting, or bring the fitting in to match it.
Can I reuse winterizing plugs?
Yes, if they are in good condition. Check O-rings and rubber for cracks or flattening each season, and replace any plug that no longer seals tightly.
Do I need pool antifreeze if I use winterizing plugs?
Some pool owners in very cold regions add pool-rated antifreeze to the lines as backup. If you use it, follow the product label and use only antifreeze made for pools, never automotive antifreeze.
Do I need to plug lines if my pool stays open all winter?
No. If the pool keeps running through winter, the lines stay full and circulating, and plugs are not used. Plugs are only for pools that are shut down.
Get Your Winterizing Supplies
Ever-Klear Pool Supply stocks threaded plugs, duck-bill plugs, skimmer plugs, and other closing supplies in our winterizing products collection, along with winter pool covers. When spring comes, our pool opening checklist walks you through getting everything running again.