A cartridge filter tells you when it needs attention: the pressure gauge climbs and the water flow drops. Clean the cartridge when the gauge reads about 8–10 psi above its clean starting pressure, which is the trigger Pentair publishes for its Clean & Clear Plus filters and a sound rule for most cartridge filters. This guide walks through when to clean, how to do it safely, when a deep soak is worth it, and how to tell a cartridge is finished and needs replacing.
When to Clean a Pool Filter Cartridge
Go by the pressure gauge, not the calendar. As the cartridge traps dirt, pressure inside the tank rises and circulation slows. The number that matters is the difference from your clean starting pressure, the reading right after a fresh or freshly cleaned cartridge goes in.
- Write down your starting pressure after every cleaning. A piece of tape on the filter tank works.
- Clean at about 8–10 psi above that number, or sooner if you notice weak returns or a skimmer that barely pulls.
- Variable-speed pump? Pressure changes with pump speed. Record your starting pressure at a specific RPM and always compare readings at that same RPM, as Pentair's manual directs.
If the gauge is stuck, fogged, or reads zero while the pump runs, replace the gauge before relying on it. A 0–60 psi stainless pressure gauge with 1/4-inch threads fits many residential filter lids; confirm the thread size on your filter before ordering.
Do Not Over-Clean
Every cleaning puts some wear on the filter fabric. Hosing the cartridge every few days when the gauge has barely moved shortens its life without a real benefit. Let the gauge decide.
Safety First: Depressurize the Filter
A pool filter is a pressure vessel. Opening one that still holds pressure can blow the lid or clamp off with enough force to cause serious injury. Before you touch the clamp:
- Turn the pump off at the breaker or timer, and make sure automation or a timer cannot restart it while you work.
- Open the manual air relief valve on top of the filter.
- Stand clear and wait until the pressure gauge reads zero.
- Open the drain plug to let the tank empty, then follow your filter manual's procedure for removing the clamp and lid.
Follow the owner's manual for your specific filter. Clamp designs and lid procedures differ between brands and models.
How to Clean a Pool Filter Cartridge: Step by Step
Step 1: Remove and Inspect the Cartridge
Lift the cartridge straight out. Before cleaning, check for damage that cleaning will not fix:
- Torn or separated pleats
- Cracked or crushed end caps
- A collapsed or bent center core
- Fabric that feels stiff or slick even when wet
Any of these means the cartridge should be replaced, not cleaned.
Step 2: Hose It Down Pleat by Pleat
Stand the cartridge upright and spray between each pleat at a downward angle, working from top to bottom. Rotate the cartridge as you go until the water running off is mostly clear. Use an ordinary garden-hose nozzle. A pressure washer can fray and tear the filter fabric.
For a routine cleaning, this is often all you need. Reinstall, restart, and check that pressure returns close to your starting number.
Step 3: Degrease When Rinsing Is Not Enough
Sunscreen, body oils, and lotions coat the fabric in a film that a hose cannot remove. If pressure stays high after a thorough rinse, soak the cartridge in a cartridge cleaner or degreaser made for pool filters, following the product label for mixing ratio and soak time. Rinse thoroughly afterward so no cleaner foams up in the pool.
Biguanide (Baquacil-type) pools: use only a cartridge cleaner approved for biguanide systems. Standard cleaners and chlorine-based products can react with biguanide residue.
Step 4: Acid Soak Only for Mineral Scale, and Only After Degreasing
In hard-water areas like much of Arizona, calcium can build up in the pleats as a white or gray crust. An acid soak removes that scale, but the order matters. Cartridge manufacturers advise degreasing first: acid applied to an oily cartridge can set the oils deeper into the fabric and permanently restrict it.
If you do acid-soak:
- Degrease and rinse completely first.
- Follow the acid manufacturer's label for dilution and handling.
- Always add acid to water, never water to acid.
- Wear chemical-resistant gloves and eye protection, and work outdoors.
- Never mix acid with chlorine, cartridge cleaner, or any other chemical. Use separate, clearly labeled buckets.
- Rinse the cartridge thoroughly before reinstalling, and dispose of the solution as the label and local rules require.
If you are not comfortable handling acid, replacing a heavily scaled cartridge is a reasonable alternative.
Step 5: Reassemble and Restart
- Inspect the tank O-ring for cracks, flat spots, or stretching. Clean it and apply a light coat of silicone-based lubricant such as Magic Lube II silicone lubricant. Do not use petroleum-based products like petroleum jelly, which can swell rubber seals.
- Close the drain plug, seat the cartridge, and reinstall the lid and clamp exactly as the manual describes.
- Open the air relief valve, start the pump, and close the valve once a steady stream of water (not air) comes out.
- Write down the new clean starting pressure.
Cleaning Method Quick Reference
| Problem | Sign | What to do |
|---|---|---|
| Loose debris | Pressure up 8–10 psi; visible dirt in pleats | Hose rinse |
| Oils and lotions | Pressure stays high after rinsing; fabric feels slick | Degreaser soak, then rinse |
| Calcium scale | White or gray crust; stiff fabric after degreasing | Acid soak after degreasing, per label |
| Physical damage | Torn pleats, cracked caps, collapsed core | Replace the cartridge |
| Worn out | Full cleaning no longer brings pressure down | Replace the cartridge |
When to Replace a Pool Filter Cartridge
Pentair's guidance for its Clean & Clear Plus filters puts average cartridge life at around three years under normal conditions, and the practical test is simple: replace the cartridge when a complete cleaning no longer brings pressure back near your starting reading. Replace it right away if you find tears, crushed end caps, or a collapsed core, since damaged media lets dirt pass straight back into the pool.
Many pool owners keep a second cartridge on hand. You can swap in the clean spare, keep the pool running, and give the dirty cartridge a proper overnight soak.
Finding the Right Replacement
Match the replacement by your filter's brand and model number (printed on the tank label), or by the part number on the old cartridge's end cap. Diameter, length, and the center-hole size on each end all have to match. Browse replacement filter cartridges, or narrow by brand with Pentair-compatible cartridges and Hayward-compatible cartridges. If you are not sure which cartridge you need, bring the old one into the store or send us the filter model number and we will help match it.
Why Filter Care Matters in Arizona
Desert pools load filters with dust, monsoon debris, and calcium from hard fill water. A restricted cartridge cuts circulation, which leaves sanitizer struggling to keep up and gives algae a foothold. That is one of the most common causes covered in our guide to why pools turn green in summer. Cooler months, when chlorine demand is lower and the pool is used less, are a good time for a thorough cleaning or a cartridge replacement before next season.
Frequently Asked Questions
How often should I clean my pool filter cartridge?
When the pressure gauge reads about 8–10 psi above your clean starting pressure, or when you notice a clear drop in flow. Depending on debris, bather load, and filter size, that can be every few weeks in summer and much less often in cooler months.
Can I use a pressure washer on a filter cartridge?
No. A pressure washer can tear the fabric and push debris deeper into it. Use a standard garden hose with a spray nozzle.
Why is my filter pressure still high after cleaning?
The most likely cause is oil or mineral scale a hose rinse cannot remove, which calls for a degreaser soak and, if needed, an acid soak. If a full cleaning does not help, the cartridge is likely worn out. Also check for a partly closed valve on the return side or a faulty gauge.
Can I put a dirty cartridge back temporarily?
It will filter, but expect higher pressure and lower flow. A spare cartridge is the easier way to keep the pool running while the original soaks.
Need Help Choosing a Cartridge?
Ever-Klear Pool Supply carries replacement cartridges for most major residential filter brands, along with the gauges, O-ring lubricants, and parts that keep a filter running well. Shop filter cartridges online, or contact our team with your filter model number for help finding the right fit.